Accessories

Pumps and Gauges for Inflatable Boats and Boards

Working pressure for each chamber

Sea Eagle’s 385ft FastTrack V-bottom kayak shows why you need to check each chamber: its side chambers have a working pressure of 3.0 to 3.5 pounds per square inch (PSI), while its floor’s recommended working pressure is 5 to 8 PSI.1 The floor’s 10 PSI maximum is a ceiling, not its routine target.1

  • Kokopelli specifies 2.0 PSI for the Platte’s side chambers.6
  • Sea Eagle lists up to 3.5 PSI as the side-chamber inflation pressure for its 380x Explorer.7
  • ROC’s FAQ recommends 12 PSI for the board body, depending on rider height and weight and the air temperature.8

ROC’s manual says to continue pumping until the pump gauge reads 10 to 15 PSI and not to exceed 15 PSI. It notes that working pressure may be lower in direct sunlight and says to use less pressure if extended periods of bright sunshine are expected.9

Choose a pump for your model

A chamber is a separately inflated compartment. PSI means pounds of air pressure per square inch.

A hand pump needs no electrical connection. With a double-action pump, air moves on both the push and pull strokes. A pump can also change to single action, which pumps on one stroke.

Sea Eagle’s Bravo 4 automatically switches from double action to single action as pressure rises; ROC’s included pump changes between high-capacity, double-action mode and high-pressure, single-action mode.2,9 iROCKER describes its hand pump as dual-chamber and triple-action.10

Electric pumps

A 12-volt electric pump may use a car power outlet or a 12-volt battery. BOTE supplies the AeroPump Mini with a 12-volt cigarette-lighter adapter.11

Aquaglide says its Accelerator HP 12V 20 Pump can reach 20 PSI and inflate Aquaglide items using its 12-volt vehicle adapter.12 Aquaglide’s 2024 page described the Accelerator HP 12v 20 as a two-stage digital pump with auto shut-off.13

If you fly with spare lithium-ion or lithium-metal batteries for your pump, the Federal Aviation Administration’s PackSafe guidance requires them to travel in carry-on baggage only, never in checked baggage.14

Pump stages and power

For the FastTrack, Sea Eagle says to use only pumps designed for inflatable boats and SUPs, never tire or construction-tool compressors, and to use a pump with automatic shut-off. iROCKER describes its Electric Pump as a two-stage pump with a digital PSI display and automatic shut-off.

“Two-stage” describes the electric pump’s airflow and pressure stages; it does not mean that a hand pump is double-action.4,5 OutdoorMaster lists dual-stage inflation and a digital pressure display for its SHARK II Electric Sup Pump.15

In an archived copy of its product page captured 6 October 2026, OutdoorMaster listed its SHARK 3 Rechargeable Electric Sup Pump at $179.99.16 OutdoorMaster lists its CACHALOT 2 Mini Electric Sup Pump as requiring a 12-volt DC connection, with no battery.17

PumpWhat the maker specifiesPower or connection
Sea Eagle Bravo 4Double action pumps on the up and down strokes. It switches automatically to single action above about 6 PSI. Its product page says Stage I, the lower-pressure stage, inflates up to 5.8 PSI; Stage II, the higher-pressure stage, is capable of 11.6 PSI.2,18Manual pump; supplied with a gauge and two hoses with pre-attached adapters.2
ROC Explorer’s included hand pumpROC describes the supplied pump as dual-action. The manual says to use dual action from 0 to 10 PSI and high-pressure single action from 10 to 15 PSI.3,9Manual pump; the manual describes changing modes by opening or closing the pump’s valve.9
iROCKER Electric PumpiROCKER describes two-stage inflation, a digital PSI display and automatic shut-off.4Connect to a vehicle power outlet or 12-volt battery; ULTRA instructions also describe alligator clips, which connect the pump directly to a 12-volt battery.5,19

Check the pump’s stated capability

Check the pressure label or manual for your own boat or board, then compare it with the pump’s stated capability. OutdoorMaster rates its DOLPHIN Electric Sup Pump for pressures up to 20 PSI.20 Yachting World lists a maximum pressure of 20 PSI for the Aquaglide Accelerator 12V High-Pressure Pump.21 The 385ft FastTrack’s different side and floor targets are specific to that kayak; do not apply them to another model.1

Bluefin says its Cruise board is tested up to 28 PSI, but recommends inflating it to 15 to 18 PSI.22

For boards covered by iROCKER’s 2023 owner’s manual, the recommended board pressure is 15 PSI, although the manual says the board can hold up to 20 PSI. 23 For an iROCKER ULTRA board, check the recommended pressure on the valve flange around that product’s inflation valve.19

NRS says its Escape Inflatable SUP Boards inflate to 20 PSI (1.379 bar).24 Red Paddle Co generally suggests aiming for 15–22 PSI for its paddleboards.25

Electric pump claims

iROCKER says its Electric Pump inflates most SUPs to their recommended pressure in about 10–12 minutes; it also claims its Power Pump Max inflates a 10-foot-6-inch SUP to 15 PSI in about 9 minutes.4

Let the pump rest between sessions to prevent overheating during multiple inflations. These are maker claims, not a comparison on the same board.4 iROCKER says the CRUISER ULTRA 3.0’s included electric pump inflates the board in under 10 minutes.26

Air Box Mini travel

Ride Engine says its Air Box Mini must travel in carry-on luggage rather than a checked equipment bag, and advises checking before every major trip because airline and international regulations can vary.27

Read the gauge as you inflate

A gauge, also called a manometer, displays air pressure. Choose a gauge with a fitting compatible with your valve setup, a measurement range that includes your target pressure, and scale divisions fine enough to distinguish it.

For the FastTrack’s 3.0–3.5 PSI side target, Sea Eagle’s manual shows a hand-pump gauge with 1 PSI divisions, so read the inner red PSI ring; if your pump is different, check Sea Eagle’s instructions page.1

Sea Eagle’s FastTrack manual identifies the inner red numbers on its dial as PSI and the outer ring as bars, a metric pressure unit; each red line is 1 PSI.1

Gauge pressure early in inflation

A gauge can show little or nothing early in inflation.

ROC says its pump typically does not show pressure until about 5 PSI, and that a board can look and feel full enough to stand on around 3 PSI. iROCKER’s manual says its board’s gauge may begin to register when the board reaches 3 to 7 PSI, depending on the pump.8,23 That early appearance is not a reason to stop: continue toward the pressure specified for your model.

Check a reading

If a reading seems wrong on an iROCKER pump, check that the gauge is secure and the dial is not stuck between settings.10

On a Sea Eagle Bravo 4, connect the gauge and hose, cover the hose outlet with a finger, then push the pump handle down sharply. The gauge should move and return to zero; if it does not, contact the maker about the gauge.2

Connect, inflate and recheck

The valve is the opening where the pump hose attaches to the chamber. The adapter is the fitting that joins the hose to that valve. Before pumping, confirm you have the correct adapter and that the connection stays in place.

AirKayaks explains that Boston valves have a screw-on base and an upper inflation valve, with an internal flap that opens during pumping and closes to prevent air escaping between strokes.28

NRS identifies Leafield B7 valves on its rafts built between 1996 and February 1999, and C7 valves on its rafts built after February 1999.29

Inflate to your model’s specified pressure

  1. Check your model’s pressure label or manual, identify the target for each chamber, and select the matching adapter.
  2. Attach the hose to the valve. ROC says to remove the valve cap and make sure the valve pin is in the closed (up) position, then insert its hose fitting and turn it clockwise; the fitting should lock in place. For Sea Eagle’s Bravo 4, the manual says the valve stem, the valve’s central pin, should be up for inflation. Use its flat adapter for the inflatable seat’s valve and its black hooked adapter for the boat’s valve. Inflate the seat only until firm; do not overinflate.9,2
  3. Inflate using the pump mode specified for your pump. ROC’s manual recommends using the supplied hand pump’s dual-action setting from 0 to 10 PSI and its high-pressure setting from 10 to 15 PSI.9 The Sea Eagle Bravo 4 switches modes automatically, so keep pumping while monitoring the gauge.9,2
  4. Stop at your model’s specified working or recommended pressure. Do not treat the maximum as the target. ROC says not to exceed 15 PSI for boards covered by its manual.8,9
  5. Disconnect the hose and replace the valve cap as your model’s manual directs. ROC says a small burst of air as its hose is removed is normal, then directs owners to secure the cap with a clockwise twist.9 When you later pack away a ROC board, ROC says to press the valve stem down and give it a gentle quarter-turn clockwise to lock it open for deflation.8

Check the connection

If an adapter feels too tight on a Sea Eagle Bravo 4, its manual says to stretch the red gasket to soften it and orient the gasket groove outward. For Sea Eagle’s FastTrack, Bravo pumps require a black or red gasket; other manufacturers’ adapters may offer several gasket thicknesses, and Sea Eagle says the thinnest works best with its valves.2,1

If air continues to escape at the connection, check that the hose is firmly attached, then inspect the valve and hose setup using your maker’s instructions.4 NRS recommends spraying soapy water in and around the valve after reassembly to check for leaks.30

For leakage from the core assembly of its D7 valve that persists after flushing and rinsing, Leafield Marine says to use service tool C16605 with the buoyancy deflated, unscrew the core of the valve counterclockwise, then check the core’s rubber seal for dirt or damage.31

Check inflation before each outing

Sea Eagle says to check inflation before each outing. Its FastTrack manual also says very cold water can cause air inside to contract and lower pressure; if pressure keeps falling and temperature is not a factor, look for a leak.

For iROCKER boards, the manual warns that heat can raise pressure and damage seams, so follow its care instructions and avoid over-inflation. When the board is out of the water, keep it in the shade.1,23

For a shore break without shade, iROCKER recommends releasing 2 to 3 PSI from its inflatable board to give the air room to expand.32 For one of its boards stored inflated and unused for a while, Red Paddle Co recommends reducing the pressure below 15 PSI and keeping the board cool and dry.33

More on inflatable kayaks and board setup

Footnotes

  1. https://www.seaeagle.com/img/PDF/HullInstructions/FTN.pdf ↩ ↩2 ↩3 ↩4 ↩5 ↩6 ↩7 ↩8

  2. https://www.seaeagle.com/img/PDF/AccessoryInstructions/19.pdf ↩ ↩2 ↩3 ↩4 ↩5 ↩6 ↩7 ↩8

  3. https://www.rocoutdoors.com/products/explorer ↩ ↩2

  4. https://irockersup.com/blogs/stories/best-electric-sup-pump ↩ ↩2 ↩3 ↩4 ↩5 ↩6

  5. https://cdn.shopify.com/s/files/1/0559/6944/7990/files/BY_IROCKER-OWNERS_MANUAL-2023-PREVIEW-V3.pdf?v=1679505714 ↩ ↩2 ↩3

  6. https://kokopelli.com/collections/urban-collection/products/platte-inflatable-kayak ↩

  7. Wayback Machine copy captured April 2, 2026 of https://www.seaeagle.com/ExplorerKayaks/380x ↩

  8. https://www.rocoutdoors.com/pages/faq ↩ ↩2 ↩3 ↩4

  9. https://cdn.shopify.com/s/files/1/0681/0743/6306/files/2023_User_Manual_Guide.pdf?v=1684521103 ↩ ↩2 ↩3 ↩4 ↩5 ↩6 ↩7 ↩8 ↩9

  10. https://irockersup.ca/en-ca/pages/faq ↩ ↩2

  11. https://www.boteboard.com/products/electric-aeropump-mini-12-volt-pump ↩

  12. Wayback Machine copy captured July 13, 2026 of https://www.aquaglide.com/products/c-deck ↩

  13. Wayback Machine copy captured November 14, 2024 of https://www.aquaglide.com/products/accelerator-hp-12v-22-pump ↩

  14. https://www.faa.gov/hazmat/packsafe/lithium-batteries ↩

  15. https://outdoormaster.com/products/electric-paddle-board-pump-shark-ii ↩

  16. https://web.archive.org/web/20261006152949/https://outdoormaster.com/products/shark-3-electric-sup-pump ↩

  17. https://outdoormaster.com/products/cachalot-2-mini-electric-sup-pump ↩

  18. https://www.seaeagle.com/accessories/pumps/dual-action-auto-two-stage-pump-w-pressure-gauge ↩

  19. https://cdn.shopify.com/s/files/1/0559/6944/7990/files/iROCKER_23_QUICK_START_GUIDE-ULTRA_SERIES-WEB.pdf?v=1693333054 ↩ ↩2

  20. https://outdoormaster.com/products/paddle-board-pump-electric-dolphin ↩

  21. https://www.yachtingworld.com/gear-reviews/the-best-kayak-pumps-144625 ↩

  22. https://bluefinsupboards.com/products/cruise-allrounder-inflatable-paddle-board-package ↩

  23. https://cdn.shopify.com/s/files/1/0559/6944/7990/files/BY_IROCKER-OWNERS_MANUAL-2023-PREVIEW-V3.pdf?v=1679505714 ↩ ↩2 ↩3

  24. https://www.nrs.com/nrs-escape-inflatable-sup-boards/p6s5 ↩

  25. https://red-equipment.us/blogs/sup-life/red-paddle-co-faq-what-psi-should-my-paddleboard-be ↩

  26. https://irockersup.com/blogs/stories/discover-lake-bliss-with-the-best-paddle-boards-for-lakes ↩

  27. https://rideengine.com/blogs/news/air-box-mini-maintenance-and-best-practices ↩

  28. https://www.airkayaks.com/pages/pumps-inflation/ ↩

  29. https://www.nrs.com/learn/inflatable-boat-use-care-instructions ↩

  30. Wayback Machine copy captured February 11, 2026 of https://www.nrs.com/learn/repair-leafield-c7-d7-valves ↩

  31. https://www.leafieldmarine.com/wp-content/uploads/2021/05/M-08-IS-0D7-D7-Valve-Service-Advice-Rev-01.pdf ↩

  32. https://irockersup.com/blogs/stories/inflatable-paddle-board-psi ↩

  33. https://red.equipment/pages/faqs ↩