Care and transport

Kayak Hardware and Hatches: What to Check and Care For

For a stiff cover, use the treatment for its system; Eddyline offers replacement covers if required, and Delta says its Press-Lock seal is designed for replacement if an issue arises. Published sources give no universal replacement threshold for hatch rims or bulkhead seals.1,2,3,4,5,6

Hatch, bulkhead, rudder and skeg

A hatch is a storage opening; its rim is the edge that meets the cover. A bulkhead is an internal wall that separates compartments. Wilderness Systems lists one stern bulkhead for its Pungo 125 recreational kayak.7

A rudder is a steering blade, and a skeg is a retractable blade that helps a kayak track straight. Bungee, or shock cord, is elastic deck cord; a static line is nonelastic. A pad eye is a small fitting that guides or attaches a line.

Choose where to start

Use these Well Paddled rules to choose where to start:

  • After saltwater or sandy use, start with the rudder or skeg and its controls; maker guidance calls for freshwater rinsing to remove salt and grit.3,5,4,6
  • If your kayak lives outdoors or in strong sun, start with rubber hatch-cover condition and deck-cord wear; Eddyline calls for more frequent cover protection in those conditions.2
  • After a long drive, start with fittings and compartment seals; P&H identifies road vibration as a reason bolts can loosen, and Wilderness Systems notes that transport flex can wear bulkhead seals.4,3
  • If a hatch is intact but getting stiff, check the treatment for its system before shopping for a replacement; Eddyline rubber, Delta’s Press-Lock hatch-seal system (the named seal system that determines which care instructions apply) and P&H covers have different care instructions.2,5,4
  • If lines are worn, look for a maker-described replacement; for damaged Feelfree steering controls or other P&H outfitting problems, seek dealer guidance.8,4

Choose a route

Your findingRouteTrade-off
A cover is stiff or hard to fitClear grit and use the treatment for that system: Eddyline rubber covers, Delta Press-Lock seals and P&H covers have different instructions.1,2,5,4The treatment depends on the cover system.
A Perception touring line is too loose or frayed; a Delta line or cable shows abrasion or wear; or a P&H MKII slider bar shows any flatteningReplace the line or bar as its maker describes; ask the Delta retailer for parts information.5,6,4Match the part to the named system.
A bulkhead perimeter seal is broken, a deck fitting is loose or broken, a control is damaged, or rim work is uncertainAsk the maker or dealer for repair advice and the correct part.8,3,4,9The published guidance does not establish a general owner-replacement rule for these parts.

What to inspect

If a compartment gets wet, check in this order: make sure the hatch cover is intact and securely fastened; inspect the bulkhead seal around its perimeter; then check deck fittings for looseness or breakage. Transport and paddling flex can wear bulkhead seals, but a groove in a Wilderness Systems bulkhead may be normal because it does not pass through the wall.

A small amount of water does not by itself identify a failed seal: Eddyline also lists condensation, an improperly seated cover, the bulkhead vent and loosened screws as possible causes.

Eddyline’s water test

For its Carbonlite 2000 kayaks, Eddyline’s owner’s manual describes a water test: on a dry day, on a lawn or sawhorses, put 3 to 5 gallons (about 11 to 19 liters) of water in each compartment, one at a time, then roll or lift the kayak and watch where water runs or drips out.

Water moving from one compartment to another indicates a bulkhead leak; the bulkheads have a tiny central vent hole.10 Use dry bags for items that must stay dry. If the source remains uncertain, ask the maker or dealer for advice.

Places to check for leaks

Comox Valley Kayaks’ maintenance checklist identifies the bulkhead seam, hull-to-deck seam, skeg box and rudder-pin attachments as places to check for leaks.11 Wilderness Systems says fine white lines inside a composite hull that mirror outside impact damage may indicate a resin fracture; care by material also gives P&H’s direction to contact a dealer for composite repairs.3,2

Bulkhead seals and bolts

P&H recommends periodically checking foam bulkhead seals on its polyethylene (plastic) kayaks. It notes that hatch cargo or flexing can damage a seal.

On kayaks made with Eddyline’s Carbonlite, its proprietary co-extruded plastic laminate, inspect nuts and the surrounding deck for looseness or unusual wear. After long drives, P&H advises checking its bolts because road vibration can loosen them; avoid overtightening, which can break O-ring or gasket seals, cause leaks, or damage the shell and outfitting.4,1

Deck lines, bungees and carry handles

Check deck lines, bungees, carry handles and attachment points for looseness, abrasion or fraying. Eddyline says its end carry handles should support the boat’s weight and recommends checking their ropes for wear.1

  • Before heading out, replace Perception touring shock cord or static lines that are too loose or frayed.
  • Delta calls for checking deck lines and rudder cables for abrasion or wear and replacing them as required; its selling retailer can provide parts information.
  • Eddyline describes worn bungees, perimeter lines and carry handles as replaceable.1,2,6,5

Inspect pad eyes—the small line guides—along with other deck fittings for looseness or breakage.3,12

Gelcoat and fiberglass

Sea Kayaking UK says small scuffs and surface scratches in gelcoat, the layer over glass or carbon matting, may polish out with a soft woolen buffer and marine polish.13 BoatUS says water entering a fiberglass deck’s core can cause rot or separation of the core from the fiberglass, depending on the core material, and lists a spongy feel when walked on among the signs.14

Clean, flush and lubricate

Eddyline recommends clearing sand and other material from the hatch cover and rim so the cover can seal. For its boats, the company says a freshwater rinse after each use is usually enough for general cleaning; it also recommends wiping inside bulkheaded compartments with a damp cloth.

If sand or mud affects foot-pedal movement, Eddyline says to hose the foot-pedal rails—the parts the pedals move along—clean. For Eddyline Carbonlite, use soap for cleaning and rubbing alcohol for stubborn stains, and avoid acetone, toluene, MEK, lacquer or paint thinner, and ammonia-based cleaners, as detailed in care by material.1

Pelican says its warranty excludes damage due to contact with a cleaner or chemical.15

Rinse after saltwater use

  • For Wilderness Systems kayaks used in saltwater, rinse the rudder, cables and foot controls with fresh water.
  • Delta calls for a freshwater rinse after saltwater use, especially around the rudder and the holes where its cables enter the deck.
  • P&H recommends rinsing inside and outside after use, with attention to the skeg blade and slider; its occasional deeper rinse includes the line tubes.3,5,4

Dry before storage

Paddling.com author Wayne Horodowich says he dries his kayaks to prevent water inside from freezing, because ice expands and too much ice may affect seams.16 In its Illinois winter-storage guide, Howling Wolfe Canoe & Kayak recommends leaving hatches open and the cockpit uncovered for 24–48 hours in a ventilated spot to dry before storage.17

Cleaning products

For the kayak covered by its manual, Aquaglide says not to use petroleum-based cleaners and warns that improper pressure-washer use can damage or destroy it.18 On its French site, Decathlon advises avoiding overly harsh and abrasive cleaning products, including ammonia and bleach, for its inflatable canoes and kayaks.19

Lubrication

Lubrication depends on the system. McLube says its SailKote dry coating does not attract dirt, water or contaminants, unlike oils, silicones and waxes.20 Transport Canada’s sample vessel maintenance schedule calls for checking, cleaning and lubricating mechanical parts as needed for proper operation.21

  • For its kayaks, Swift suggests using a lubricant such as Rust Check on cables and moving parts once a year.22
  • P&H recommends periodically applying silicone spray to its skeg slider—the moving control that runs along its bar—after rinsing.
  • Perception recommends scrubbing grit from moving rudder or skeg parts if they bind, then using a silicone-based lubricant.
  • For difficult-fitting P&H hatch covers, the company suggests silicone spray on the rim and inside edge of the cover.4,6

Deck plates and rubber hatch lids

Sea-Dog says to clean the threads of its screw-out deck plates with hot soapy water and lubricate them with Vaseline or Teflon grease.23 Germany’s Lettmann recommends spraying its rubber hatch lids with silicone oil or cockpit spray and wiping away the excess with a cloth.24

303 Protectant and Press-Lock hatch seals

Eddyline recommends 303 Aerospace Protectant, a protectant product for rubber hatch covers, at least once a year, and more often in very sunny regions or when stored outdoors. Perception recommends 303 Protectant or a similar plastic protectant to protect its polyethylene kayaks from ultraviolet light.6

Delta’s manual says not to use 303 Protectant on its boats. For Delta Press-Lock hatch seals that become harder to put on or take off, the manual recommends Armor All Original, a seal-care product in spray or wipe form. Keep these instructions with their named systems; they are not interchangeable.2,5

Paddling.com author Wayne Horodowich says he tries to treat rubber products twice a year with manufacturer-recommended products.16

Replace a matched part

Eddyline offers replacement rubber hatch covers and describes worn bungees, perimeter lines and carry handles as replaceable. SEA-LECT Designs says that if your kayak’s footbrace mounting holes are 14½ inches apart center-to-center, you can unscrew the old footbraces and replace them with its Adjustable Footbrace system.25

Delta describes the Santoprene (rubber) seal on its Press-Lock system as designed for replacement. For its Pry-Out deck plates (removable access covers), Beckson says to install a new gasket (sealing ring) if the existing gasket appears worn, damaged or flattened.26

P&H identifies the composite bar in its MKII Skeg Slider System as a wear part to replace once any flattening appears; skeg parts and upgrade kits are available through local dealers. These statements apply to the named products and do not establish a general owner-replacement rule for every kayak.2,5,4

Match a replacement cover

For a replacement cover, measure the hatch rim’s outside dimensions, not the old cover’s top dimensions or the nominal hatch name. Match those measurements to the rim column of Kajak Sport’s replacement-cover guide and the corresponding cover standard; rim and cover dimensions are separate. The guide lists ten rim sizes with the cover sizes that go with them; the table below gives them all.

For oval rims, compare both length and width. Before ordering, confirm your kayak’s model and year, hatch position, shape and existing standard, including whether it is Valley/VCP. If the rim itself needs work, ask the kayak’s maker or dealer which part fits; Kajak Sport’s guide does not authorize rim replacement.9

Rim and cover dimensions

Kajak Sport lists these rim and cover dimensions, converted here from the guide’s millimeters; its cover types are rubber, click-on and LRC, and the Valley rows are for Valley/VCP covers. For the four Valley rims the guide states “The Rim is not available.”9

Hatch (rim)Rim outer dimensionCover top outer dimension
KS Round Hatch 104.45 in (113 mm)Rubber 4.69 in (119 mm)
KS Round Hatch 156.46 in (164 mm)Rubber 6.69 in (170 mm); click-on 6.69 in (170 mm); LRC 6.69 in (170 mm)
KS Round Hatch 208.23 in (209 mm)Rubber 8.66 in (220 mm); click-on 8.46 in (215 mm); LRC 8.66 in (220 mm)
KS Round Hatch 2410.08 in (256 mm)Rubber 10.63 in (270 mm); click-on 10.47 in (266 mm); LRC 10.63 in (270 mm)
KS Oval Hatch 42/3017.68 by 12.91 in (449 by 328 mm)Rubber 18.15 by 13.54 in (461 by 344 mm); click-on 17.80 by 12.91 in (452 by 328 mm); LRC 18.11 by 13.39 in (460 by 340 mm)
KS Oval Hatch 44/2618.35 by 11.14 in (466 by 283 mm)Rubber 18.82 by 11.42 in (478 by 290 mm); click-on 18.50 by 11.22 in (470 by 285 mm); LRC 18.82 by 11.42 in (478 by 290 mm)
Valley Round 19.5 (standard)7.95 in (202 mm)KS (VCP) Round Hatch 19.5 cover 8.43 in (214 mm)
Valley Round 2510.55 in (268 mm)KS (VCP) Round Hatch 25 cover 10.83 in (275 mm)
Valley Round Oval 34/3014.17 by 12.40 in (360 by 315 mm)KS (VCP) Round Oval Hatch 34/30 cover 15.71 by 13.15 in (399 by 334 mm)
Valley Oval 41/2217.28 by 10.00 in (439 by 254 mm)KS (VCP) Oval Hatch 41/22 cover 17.87 by 10.79 in (454 by 274 mm)

Dealer guidance

  • For damaged cables or foot or hand controls on Feelfree’s Beaver Tail Rudder (its steering system), Feelfree advises contacting a local dealer.
  • Wilderness Systems offers replacement deck fittings and neoprene washers for deck leaks, and directs owners with repair questions to a dealer or customer service.
  • P&H directs owners with other outfitting problems to stop using the kayak and contact a local dealer for advice.

Check the maker’s guidance for your specific kayak before treating a listed replacement part as owner-replaceable.8,3,4

Where next

Footnotes

  1. https://eddyline.com/blogs/news/kayak-care-and-repair ↩ ↩2 ↩3 ↩4 ↩5 ↩6 ↩7

  2. https://eddyline.com/pages/faqs ↩ ↩2 ↩3 ↩4 ↩5 ↩6 ↩7 ↩8

  3. https://www.confluenceoutdoor.com/pages/wilderness-systems-faq ↩ ↩2 ↩3 ↩4 ↩5 ↩6 ↩7 ↩8

  4. https://phseakayaks.com/kayak-care-and-maintenance.php ↩ ↩2 ↩3 ↩4 ↩5 ↩6 ↩7 ↩8 ↩9 ↩10 ↩11 ↩12 ↩13

  5. https://www.deltakayaks.com/wp-content/uploads/2018/10/2018-delta-kayaks-owners-manual.pdf ↩ ↩2 ↩3 ↩4 ↩5 ↩6 ↩7 ↩8 ↩9

  6. https://www.confluenceoutdoor.com/pages/perception-faq ↩ ↩2 ↩3 ↩4 ↩5 ↩6

  7. https://www.confluenceoutdoor.com/products/wilderness-systems-pungo-125-recreational-kayak-9731079142 ↩

  8. https://feelfreeus.com/blogs/pro-staff/spring-kayak-tune-up-2025 ↩ ↩2 ↩3

  9. https://kajaksport.fi/wp-content/uploads/2023/06/KS-Choosing-the-replacement-cover-2023_A.pdf ↩ ↩2 ↩3

  10. https://cdn.shopify.com/s/files/1/0284/7725/9864/files/Carbonlite_Owners_Manual.pdf?v=1693257223 ↩

  11. https://www.cvkayaks.com/post/kayak-maintenance-checklist ↩

  12. https://www.confluenceoutdoor.com/products/wilderness-systems-round-pad-eyes-5-pack-9800364 ↩

  13. https://www.celticpaddles.com/articles/gel-coat-repairs-and-star-cracks ↩

  14. https://www.boatus.com/expert-advice/expert-advice-archive/2021/november/7-hidden-boat-maintenance-problems-and-how-to-fix-them ↩

  15. https://www.confluenceoutdoor.com/pages/warranties ↩

  16. https://paddling.com/learn/winterizing-you-and-your-kayak ↩ ↩2

  17. https://howlingwolfe.com/kayak-winter-storage-illinois-guide/ ↩

  18. https://www.aquaglidepaddle.com/cdn/shop/files/Chelan-140-Manual_2021.pdf?v=1689711770 ↩

  19. https://conseilsport.decathlon.fr/lentretien-et-le-nettoyage-de-votre-canoe-kayak-gonflable ↩

  20. https://www.mclubemarine.com/sailkote/ ↩

  21. https://tc.canada.ca/en/marine-transportation/marine-safety/sample-maintenance-schedule ↩

  22. https://swiftcanoe.com/wp-content/uploads/2020/09/KayakOwnersManual.pdf ↩

  23. https://sea-dog.com/groups/536-screw-out-deck-plate ↩

  24. https://lettmann.de/templates/g5_helium/custom/images/downloads/lettmann_handbuch_ENG_LY2.pdf ↩

  25. https://sea-dog.com/sc/RawData/Sea-Dog/Publications/91 ↩

  26. https://www.beckson.com/files/deckplate/180924_deck%20plate.pdf ↩